series am 30k-nz 30 watt | dc - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8. g 1 of 3 north america only features: ? rohs compliant ? trim adjustment ? remote on/off control ? power modules for pcb mounting ? high efficiency up to 90% ? operating temperature range: - 40 to + 8 5oc ? input under voltage protection ? standard package models single output model input v oltage (v) output voltage (v) output current max ( a) maximum capacitive load (f) efficiency (%) am30k - 1203s - nz 9 C 18 3.3 6 19500 85 am30k - 1205s - nz 9 C 18 5 6 10200 87 am30k - 1212s - nz 9 C 18 12 2.5 3240 88 am30k - 1215s - nz 9 C 18 15 2 1100 88 am30k - 1224s - nz 9 C 18 24 1.25 900 88 am30k - 2403s - nz 18 C 36 3.3 6 19500 86 am30k - 2405s - nz 18 C 36 5 6 10200 88 am30k - 2412s - nz 18 C 36 12 2.5 3240 89 am30k - 2415s - nz 18 C 36 15 2 1100 89 am30k - 2424s - nz 18 C 36 24 1.25 900 88 am30k - 4803s - nz 36 C 75 3.3 6 195 00 87 am30k - 4805s - nz 36 C 75 5 6 10200 89 am30k - 4812s - nz 36 C 75 12 2.5 3240 90 am30k - 4815s - nz 36 C 75 15 2 1100 90 am30k - 4824s - nz 36 C 75 24 1.25 900 90 note: all specifications in this datasheet are measured at an ambient temperature of 25c, humid ity<75%, nominal input voltage and at rated output load unless otherwise specified . input specifications parameters nominal typical maximum units voltage range 12 9 - 18 vdc 24 18 - 36 48 36 - 75 filter (pi) network start up time 25 ms absolute maximum rating 12 vin 20 vdc 24 vin 40 48 vin 80 peak input voltage time 100 ms remote on/off control on 3.5 to 12vdc or open circuit off 0 to 1.2vdc or short circuit between pin 2 and 3 under voltage protection 9 - 18 vin off 8 vdc 18 - 36 vin off 16 36 - 75 vin off 33 isolation specifications parameters conditions typical rated units tested i/o voltage 60 sec 1500 vdc resistance a t 500vdc > 1000 mohm capacitance 100khz / 1v 1000 pf
series am 30k-nz 30 watt | dc - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8. g 2 of 3 north america only output specifications parameters condit ions typical maximum units voltage accuracy 1 % line voltage regulation ll - hl 0.2 % of vin load voltage regulation 10% to 100% load 0.5 % short circuit protection continuous short circuit restart auto recovery over current protection input vo ltage range >120 160 % temperature coefficient 0.02 %/ o c ripple & noise 20mhz bandwidth 100 mv p - p transient response recovery time 25% load step change 200 s transient response overshoot 2 5 % of vout voltage adjustment range 10 % genera l specifications parameters conditions typical maximum units switching frequency 100 % load 300 khz operating temperature with derating above +71c - 40 to +85 o c storage temperature - 55 to +105 o c case temperature 95 o c cooling free air convection humidity 95 % case material copper, nickel plated weight 45 g dimensions (l x w x h) tolerance 0.5mm 2.0 0 x 1.60 x 0.42 inches 50.8 0 x 40.6 0 x 10.6 0 mm mtbf >1 000 000 hrs pin out specifications dimensions pin single 1 +v i nput 2 - v i nput 3 on/off c ontrol 4 +v output 5 - v o utput 6 trim 4 0 . 6 0 ( 1 . 6 0 ) 50 . 80 ( 2 . 00 ) 1 2 3 4 5 6 bottom view 45 . 72 ( 1 . 80 ) 1 0 . 1 6 ( 0 . 4 0 ) 1 0 . 1 6 ( 0 . 4 0 ) 1 0 . 1 6 ( 0 . 4 0 ) 5 . 0 8 ( 0 . 2 0 ) 1 1 . 8 0 ( 0 . 4 7 ) ? 1 . 50 ( 0 . 06 ) 5 . 1 0 ( 0 . 2 0 ) printed face 7 . 6 2 ( 0 . 3 0 ) 2 . 54 ( 0 . 10 ) 2 . 54 ( 0 . 10 ) 4 . 1 0 ( 0 . 1 6 ) case tolerance 0 . 50 ( 0 . 02 ) pin pitch tolerance 0 . 35 ( 0 . 014 ) dimensions mm ( inch )
series am 30k-nz 30 watt | dc - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r8. g 3 of 3 north america only trimming derating recommended emi filtering (if required by end application) note: should your application not require filtering, no additional circuits are required. v+ v- vo+ vo- input + input - load lcm ( 3.8mh) am30k-nz note: 1. datasheets are updated as needed and as such, specifications are subject to change without notice. once printed or downloaded, datasheets are no longer controlled by aimtec; refer to www.ai mtec.com for the most current product specifications. 2. product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specificat ions are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemical s at the time of publishing this document. cas numbers and other limited information are considered proprietary and may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous en vironments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. warranty is in accordance with aimtecs standard terms of sale available at www.aimtec.co m. free air convection - 40 - 20 0 20 40 60 80 100 100 80 60 40 20 0 safe operating area o u t p u t po w e r (% ) 85 ambient temperature o c 71 c o
|
